The Department of Commercial Design, National Taichung University of Science and Technology, No.129, Sec.3, Sanmin Rd, North Dist, 404 Taichung, Taiwan ↗
The circular economy of recycled plastics is gradually emerging. Its objective is to reduce the production of new plastics, design products with recycled plastics according to the thermoplastic characteristics of plastics, classify, wash, dry, finely shred, and then melt and remanufacture waste plastics to reshape the appearance and function of products. In this study, consumers’ acceptance, cognition, and preference for recycled plastic products were explored based on the image these products carry. A total of 11 commercially available recycled plastic products were collected, which were respectively made of propylene (PP), high/low-density polyethylene (HDPE/LDPE), and poly (ethylene glycol-co-1,4-cyclohexanedimethanol terephthalate) (PETG), and shaped by the injection moulding machine, compressor, tablet press, and 3D printing. These adjectives were used for the survey of 100 subjects for their evaluation of recycled plastic products. The consumers’ preference for the material of the recycled plastic products is in the order of HDPE/LDPE > PETG > PP. In addition, the evaluation of those using moulds in the manufacturing process is high, which can achieve a better product image and win consumer preferences. In the sample products of this study, a recycled watch strap is made of LDPE material using the injection moulding machine.
RESEARCH OBJECTIVES AND MOTIVATIONS In recent years, many designers have used recycled waste plastics in new pro- ducts, contributing to the circular economy in which resources are infinitely recycled. In literature related to the waste plastic recycling process, such as the development of a plastic shredder (Ekman, 2018), the thermoplastic cha- racteristics of plastics are used to make recycled products that eventually return to consumers. In this study, the discussion of plastic properties and process technology is extended. A total of 11 sample products are considered from a collection of commercially available recycled plastic products, and a survey on the image of these products is conducted to determine consu- mers’ perceptions and preferences of recycled plastic products to facilitate the development of manufacturing technology for recycled plastics.
LITERATURE REVIEW
(1) Injection moulding: More than 30% of plastic handicrafts are made by injection moulding. The injection moulding machine heats and melts the
plastic and then extrudes it. Singh (2016) found that temperature, pressure generated during injection, and injection speed affect the tensile strength of plastics. This injection moulding technology is suitable for products with high demand and repeatability, making it possible to fully exploit the repe- ated usage of moulds, leading to fast production and high precision. (2) Compression Machine: The compression machine uses the concept of oven heating technology, in which plastics are melted and compressed into large- scale moulds. The principle is to compress the shredded plastics by heat and pressure. However, the plastic becomes fluid or granular in shape during the compression process, and the manufacturing process is time-consuming and only suitable for large-scale products (Gordeev, 2019). (3) Extrusion Machine: Based on the principle of industrial single-screw extruder, the waste plastics are melted and extruded. The plastics are transferred to the heating tube through the screw rod, and then extruded after being melted in the hea- ting tube. The viscosity of the material, design of the screw, and speed of the screw affect the performance of plastic extrusion (Abeykoon et al., 2021). (4) Sheet Machine:The sheet machine shapes the products by heating and extru- sion. The extrusion duration affects the thickness of the sheet. The longer the extrusion duration, the thinner the sheet will be (Wongsangnoi et al., 2021). (5) 3D Printing: 3D printing is often used in auto parts, medical equipment, toys, etc. A plastic shredder is used to smash the waste plastics into small pieces, which are then melted and extruded into thin wires through a plastic extruder. The thin wires can be used as the raw material for 3D printing, which is sent to a 3D printer and converted into a valuable product (Mikula et al., 2021).
RESEARCH METHOD AND PROCEDURE First, 11 commercially available recycled plastic products were collected as samples and analysed.Finally, the survey results were summarised and analy- sed to understand the subjects’ cognition of recycled products and product preferences. The 5-point Likert scale was used to measure the evaluation of 100 subjects on the perceptual image of recycled plastic products.
Sample Collection and Classification In this study, recycled products sold in online and offline stores were colle- cted, and 11 main samples with relatively good sales volume were selected, the raw materials of which were respectively PP, HDPE/LDPE, and PETG. In the subsequent analysis of this study, HDPE and LDPE were treated as PE and analysed as the same category, the moulding methods of which include using injection moulding machine, compression machine, sheet machine, and 3D printing. The practice of using moulds in the manufacturing process or not is treated as an important factor. In addition, to avoid the subjects being influe- nced by other factors during their evaluation of the products, the background of the products is removed, as shown in Table 1.
Survey on Cognition and Preference for Recycled Plastic Products To analyse the consumers’ understanding of plastic recycling, as well as their acceptance and preference for recycled plastic products, the survey
Customer Preference of Recycled Plastic Products 123
Table 1. Recycled plastic product samples and classification results.
Table available in the original PDF paper.
was focused on understanding the basic cognition of the subjects on pla- stic recycling, such as whether they have the basic understanding of plastic recycling, accept recycled products, and understand the existing plastic recycling mechanisms in Taiwan. The survey investigated their preference for recycled products to confirm the acceptance of recycled plastic produ- cts in the consumer market. The survey data obtained was then analysed to establish the correlation between the perceptual adjectives and the elements of the product to determine the needs of the subjects and preferred design features and understand the preferences of consumers.
RESULT ANALYSIS AND DISCUSSION Difference in Cognition Due to Previous Purchase of Recycled Products
Regression analysis was used to analyse the influence of consumers’ pre- ferences on purchasing intention and cognition of recycled products. The
124 Lin and Yang
Table 2. Analysis of difference in willingness to purchase recycled products and cognition.
Estimated Standard Beta B value error distribution −.189 .070 −.320 −2.704 .008
Repulsion to using recycled plastic products
.165 .074 .263 2.220 .029
Willingness to purchase recycled plastic products
−.187 .049 −.422 −3.807 .000
Understanding of plastic recycling and manufacturing
−.031 .049 −.069 −.626 .533
Understanding of existing plastic recycling mechanisms in Taiwan
different modes, including repulsion to using recycled plastic products, wil- lingness to purchase recycled plastic products, and understanding of plastic recycling and manufacturing process, all had a significance level <0.05, indi- cating that the 100 subjects aged between 25 and 55 had a certain level of understanding of the manufacturing process of recycled plastic products (table 2), as well as no repulsion to using recycled plastic products and the willingness to purchase recycled plastic products. However, many consumers were still unclear regarding the plastic recycling process.
Consumers’ Preference for Recycled Products
Table 3 (A) shows the quantitative analysis of consumers’ preference for recycled products. The three types of plastics analysed include PP, HDPE- /LDPE, and PETG. As shown by the scores, the consumers’ preference is in the order of HDPE/LDPE (0.24) > PETG (0.23) > PP (−0.17). Moreover, it is shown that consumers prefer products made using moulds. The larger the value of the multiple correlation coefficient, the more linear is the relation- ship between the elements and variables. Therefore, in comparison to mould use, the plastic used in recycled products had a larger influence on consumers’ preferences.
In Table 3 (B) and Table 3 (C). The scores indicate that consumers’ prefere- nce follows the order of HDPE/LDPE > PETG > PP, and products made using moulds have relatively high evaluations. The partial correlation coefficients of plastic and mould use were calculated and compared, which revealed that the influence of plastic type on consumers’ preference for the recycled pla- stic products was larger than that of mould usage during the manufacturing process.
Customer Preference of Recycled Plastic Products 125
Table 3. Consumers’ preference for recycled products in three perspectives.
Table available in the original PDF paper.
B Influence of integrated factor of recycled products
C Influence of gorgeous factor of recycled products
Multiple correlation coefficient = 0.60 0.64 0.59 Coefficient of determination (Square of multiple correlation coefficient) = 0.36
CONCLUSION
Consumers are less aware of the plastic recycling process in their daily life. To strengthen environmental protection measures, the government needs to actively promote plastic recycling. In addition, it is found that PE, including the HDPE and LDPE analysed in this study, and products made with moulds are preferred by consumers. Among the sample products, a recycled watch belt is made of LDPE using injection moulding. Further comparison reve- als that the plastic material is a key factor influencing consumers’ choice of recycled products, which should be the main design element. The results of this study not only help understand the consumers’ acceptance and prefere- nce for recycled plastic products but also reveal the plastic type that has a relatively large influence. In the linear consumption model of the economy, energy sources are developed, manufactured, used, and discarded on a large scale, which causes environmental pollution and energy depletion. To faci- litate energy recycling, the perceptual image of recycled plastic products is explored to discuss the feasibility of recycled plastic products. The analysis results can be further applied to the design-making in the design of recycled plastic products in the future.
REFERENCES
C. Abeykoon, A. McMillan and B. K. Nguyen, Energy efficiency in extrusionrelated polymer processing: A review of state of the art and potential efficiency improvements, Renewable and Sustainable Energy Reviews 147 (2021) 111219. G. Singh, Dr. A. Verma, A Brief Review on injection moulding manufacturing pro-
cess, 5th International Conference of Materials Processing and Characterization (ICMPC 2016), India. K. Mikula, D. Skrzypczak, G. Izydorczyk, J. Warcho, K. Moustakas, K. Chojnacka and A. Witek-Krowiak, 3D printing filament as a second life of waste plastics–a review, Environmental Science and Pollution Research (2021) 28: 12321–12333.
126 Lin and Yang
N. Gordeev, Organising Waste Management in Marsabit County (2019). P. Wongsangnoi, N. Pianthong and N. Pannucharoenwong, The application of quality function deployment for the development of rubber sheet machine, Psychology and education 58(2) (2021) 4721–4728. R. Ekman, Development of a Plastic Shredder (2018).
LISTED IN THE AHFE DIGITAL BOOKSTORE CATALOGUE
Explore the complete digital volume
Kansei Engineering
Read this individual research paper free through the original publisher, or explore the full digital proceedings book.
ISBN 978-1-958651-16-2
Explore this ISBN in the AHFE Bookstore ↗Listed in the July 2026 bookstore catalogue; search by ISBN to confirm current availability · Digital book purchase optional